Designation: F /F M – 02An American National Standard Standard Speciﬁcation for Referenced Documents ASTM Standards: D Practice for. ASTM F/FM Standard Specification for Chlorinated. Poly(Vinyl Chloride) (CPVC) Plastic Pipe Schedules 40 and View on Information Provider. CPVC Schedule 40 and Schedule 80 pipe shall be manufactured in accordance to the requirements of ASTM F for physical dimensions and tolerances.
|Published (Last):||17 April 2006|
|PDF File Size:||10.35 Mb|
|ePub File Size:||16.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Lower pressure rating than those calculated in accordance with 8. Originally approved in These notes and footnotes excluding those in tables and figures shall not be considered as requirements of aetm specification.
Add to Alert PDF.
On removal of the load examine the specimens for evidence of splitting, cracking, or breaking. Included are criteria for classifying CPVC plastic pipe materials and CPVC plastic pipe, a system of nomenclature for CPVC plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, burst pressure, flattening, and extrusion quality. Link to Active This link will always route to the current Active version of the standard.
However, tests on larger pipe have shown these stress values to be valid. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. A minimum of six specimens shall asrm tested. Last previous edition approved in as F — Methods of marking are also given.
Test an additional three specimens at a single pressure that will result in failures at about h. Current edition approved Nov.
Asgm of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Test three specimens at a single pressure that will result in failures at or below 0. When the indicated pressure rating is lower than that calculated in accordance with 8. Within the text, the SI units are shown in brackets.
The industry does not recommend threading CPVC plastic pipe in Schedule 40 dimensions in nominal pipe sizes 6 asgm. Pressurized compressed air or other compressed gases contain large amounts of stored energy which present serious saftey hazards should a system fail for any reason. Government procurement requirements should not be construed as an indication that the U.
ASTM Fpdf – Free Download PDF
The test shall be conducted in accordance with 8. Additional information regarding the test method and other criteria used in developing these hydrostatic design stresses may be obtained from the Plastics Pipe Institute, a division of The Society of the Plastics Industry, K Street NW, SuiteWashington, DC A specific precautionary statement is given in Note 7.
The rate of loading shall be uniform and such that the compression is completed within 2 to 5 min. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. These dimensions conform to nominal IPS dimensions. This standard does not purport to address all of the safety concerns, if any, associated with its use.
Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases some manufacturers do not allow pneumatic testing of their products. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
A specific precautionary statement is given in Note 6. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.
ASTM F441/F441M – 15
Within the text, the SI units are shown in brackets. NOTE 3—Pressurized compressed air or other compressed gases contain large amounts of stored energy which present serious saftey hazards should a system fail for any reason.
The producer may use his own or any other suitable facilities for the performance of the inspection and test requirements specified herein, unless the purchaser disapproves. These hydrostatic design stresses may not be suitable for materials that show a wide departure from a straight-line plot of log stress versus log time to failure.
Your Alert Profile lists the documents that will be monitored. This standard does not purport to address all of the safety concerns, if any, associated with its use.