Provides information to enable POS operators to use the TM-. L90 safely and correctly. TM-L90 Service Manual. Describes maintenance, inspection and repair . EPSON has been taking industryinitiatives with its own POS printer . TM-L90 with Peeler User’s Manual TM-L90 peeler specification safely and correctly. Epson TM-L90 is a label printer for retail printing with receipt and greyscale printing. It also has greyscale for multi-tone printing.
|Published (Last):||15 August 2017|
|PDF File Size:||12.31 Mb|
|ePub File Size:||2.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Don’t show me this message again. To select partial cut: You must follow warnings carefully to avoid serious bodily injury. Be sure to set this equipment on a firm, stable, flat surface. Also, do not increase the paper width after you have used a narrower width.
EPSON TM-L90 SERIES SERVICE MANUAL Pdf Download.
Peel off the mini-clamp. Maunal the position of the cutter driving gear so that the triangle mark on the cutter driving gear becomes visible through the hole in the mxnual cutter cover assembly. Mounts horizontally, vertically or with a wall bracket Easy operation: Confidential Frame R and Center Frame 1. Remove the fixed blade holder spring by lifting up the claw. Take care not to let metal objects come into contact with the thermal head.
Confidential Label Paper Holder 1.
Remove the NE detector lead wire from the hook on the label paper holder. Remove the three S1 screws and remove the platen holder.
Test Points Confidential Test Points Test points on the main circuit board After a main circuit board unit failure, one basic method for diagnosing the cause of the problem on the main circuit board unit is to check the power supply line.
Remove the roll paper cover unit. Confidential Main Case Assembly 1. Page 14 Using Different Paper Widths Be sure to set the paper width with the memory switch to match printing to the print width. Remove the two E-rings E2.
Has been successfully added to your basket Continue shopping Go to checkout. Table of Contents Add to my manuals Add. With the roll paper cover opened, majual the power on while pressing the FEED button. The steps below show the setting of the cutting method.
This job may be performed only after turning off the printer and waiting for approximately 10 minutes. Page 39 Confidential 5. Be sure to hold the two head holder springs while removing spring holder plate. Remove the sub circuit board assembly by pulling it up manuql and out. When removing the screws near the platen gear, take precautions against touching the gear with the screwdriver.
Epson TM-L90 series Service Manual
Adjusting screw Fixed position 1 diameter: Set the detector based on whether your printer is installed vertically or horizontally. Doing so may cause failures. Slide tm-,90 label paper spacer to the appropriate width. Lift up and remove the cutter cover by inserting a flathead screwdriver or similar tool into the cutout in the main case assembly and spreading it in the direction of an arrow.
Register now We respect your privacy. We respect your privacy. Remove the two head holder springs from the spring holder panel by rotating mqnual.
Page of 17 Go. To select full cut: To print the manual completely, please, download it. The following original paper manial can be used. Confidential Test Points on the Printer Mechanism Before you replace the main circuit board to see if the printer is repaired, you need to check the printer mechanism. Test Points On The Printer Mechanism Confidential Test Points on the Printer Mechanism Before you replace the main circuit board to see if the printer is repaired, you need to check the printer mechanism.
Do not connect cables other than as described in this manual.
Cut the plastic sheet with a cutting tool such manuzl a cutter knife. The easy-to-use operator cover and lifespan of up to 20 million lines enable long-lasting, trouble-free maintenance. Troubleshooting Do not damage the thermal head by touching it with your fingers or any hard object. See the illustration on the right below. Page 71 Confidential 8.
This process is necessary only if the original NE detector lead wire has insulation tape affixed. Disconnect the lead wire of the BM paper detector circuit board assembly from the switch circuit board assembly, and remove the ferrite core.
Epson TM-L90 Series – Epson
Page 81 – Adjusting the Detecting Point of the Mwnual When any error shown below occurs, turn off the power as soon as possible. Remove the main case assembly. Remove the epwon wires of the BM black mark paper detector circuit board assembly from the roll paper cover unit.
Page 47 Confidential Hinge Cover 1. Connecting Cables Even if you can see two holes, this is the only one to put the screw in.