Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail. Dedication to. Dixell. Installing and Operating Instructions rel /02/ – cod. or faulty operation send the instrument back to the distributor or to “Dixell s.r.l.” (see. Digital controllers suitable for both heating and cooling applications. • Built in RS for connection to Dixell’s monitoring system. • Temperature control can be .
|Published (Last):||15 October 2008|
|PDF File Size:||20.92 Mb|
|ePub File Size:||7.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Parameter Fnd fan delay now becomes the delay between the start of the 1st and 2nd compressor. The x100c will then resume normal operation Sets the interval time between the start of successive defrosts.
DIXL Almost all cixel supplies are influenced by the running of other electrical equipment and will carry some ‘noise’ or transients. It is compatible with the existing sensors from most other leading brands. Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail.
Sets the time delay at the end of defrost between an alarm condition being detected and the alarm being signaled. Dixell parametric controllers, fan speed controllers and inverters, compressor controls, EEV drivers, sensors and monitoring systems are trusted around the world.
The Universal-R can be used as a service replacement for all popular 32 x 74mm format electronic refrigeration controllers listed opposite.
When you do this, you will have entered the Main Function Menu. Turns the decimal point on or off. Dixell technology is leading the way in electronic regulation xrr100c control in the fields of refrigeration, air conditioning and heating, and retail. Most normal supplies are however acceptable but where the supply is also used for large motors, fluorescent lights, etc.
Dixell – Electronic Controls Handbook |
Zr100c filter should be fitted in series to the vac supply to the control or transformer. As a result programming takes just a few minutes using the new ‘Quick Programming’ guide. Normal display is resumed once the actual temperature drops below this point or the time set in this parameter has expired ALC Alarm Configuration Configures the alarm either to absolute temperatures or to be relative to the Set Point i. Dedication to technological innovation and constant focus on efficiency have driven the development of solutions designed to xrr100c energy savings.
Setting time to 0 to disables this function Sets the period of time following a thermostat override after which the controller will go into a defrost.
Sets the initial temperature alarm delay time on start up so avoiding unnecessary alarms during pull down. Do not fit a controller in a place where it will be subjected to excessive vibration. H it H 30 mins. Sets the low temperature alarm level.
98473 – Digital Thermometer XR100C 230V
If no button is pressed for 15 seconds, the controller will revert to normal display. During the energy saving cycle, the temperature display will flash. This input type must be specified at time of order.
All relays turn off. Pr2 0 0 to mins. PTC temperature probe input models only. Click the X to close this notice. The Dixell Xr1100c can directly replace all of the following controllers for their most typical applications as well as many others not listed. Sets the time delay between the power to the controller being turned on and any output relay starting to operate.
If set for hot gas, the compressor is kept running during defrost. Innovation and efficiency for a better environment Dixell technology is leading the way in electronic regulation and control in the fields of refrigeration, air conditioning and heating, and retail.
Cooling — Differential is above the Set Point Heating — Differential is below the Set Point If a probe fault is detected the display will flash P1 and the controller will automatically cycle the compressor on and off. Push SET for 4 secs. This parameter sets the override time during which the compressor will run continuously irrespective of the temperature.
It’s a community-based project which helps to repair anything. If the existing sensors are incompatible or possibly faulty, they can be replaced by the two new PTC sensors which come supplied with the Universal-R. Dedication to technological innovation and constant focus on efficiency have driven the development of solutions designed to maximize energy savings.